国产一区二区三区毛片_亚洲乱码AV中文一区二区_亚洲精品无码专区在线播放_日韩欧美一二_咪咪av影院_欧久久av一区二区

三菱FX2N有什么指令可BIT轉移給d寄存器值
及d寄存器值反轉BIT值回中號
d寄存器最大值不知能否到255（及反轉時）或者最大到?
比如
M0 = OFF，M1 = OFF，M2 = OFF，M3 = OFF <=>則D0 = 00
M0 = ON，M1 = OFF，M2 = OFF，M3 = OFF <=>則D0 = 01
M0 = OFF，M1 = ON，M2 = OFF，M3 = OFF <=>則D0 = 02
M0 = ON，M1 = ON，M2 = OFF，M3 = OFF <=>則D0 = 03
M0 = OFF，M1 = OFF，M2 = ON，M3 = OFF <=>則D0 = 04
M0 = ON，M1 = OFF，M2 = ON，M3 = OFF <=>則D0 = 05
M0 = OFF，M1 = ON，M2 = ON，M3 = OFF <=>則D0 = 06
M0 = ON，M1 = ON，M2 = ON，M3 = OFF <=>則D0 = 07
M0 = OFF，M1 = OFF，M2 = OFF，M3 = ON <=>則D0 = 08
M0 = ON，M1 = OFF，M2 = OFF，M3 = ON <=>則D0 = 09
M0 = OFF，M1 = ON，M2 = OFF，M3 = ON <=>則D0 = 10
M0 = ON，M1 = ON，M2 = OFF，M3 = ON <=>則D0 = 11
M0 = OFF，M1 = OFF，M2 = ON，M3 = ON <=>則D0 = 12
M0 = ON，M1 = OFF，M2 = ON，M3 = ON <=>則D0 = 13
M0 = OFF，M1 = ON，M2 = ON，M3 = ON <=>則D0 = 14
M0 = ON，M1 = ON，M2 = ON，M3 = ON <=>則D0 = 15
：
：

==========以下新增另一延伸問題==========
如果要"范圍單一M"(M0~M254)轉為D寄存器值或反轉BIT值回M
M0~M254只要一個沒有ON,則D0=0
M0=ON <=>D0=1
M1=ON <=>D0=2
M2=ON <=>D0=3
M3=ON <=>D0=4
M4=ON <=>D0=5
M5=ON <=>D0=6
M6=ON <=>D0=7
M7=ON <=>D0=8
M8=ON <=>D0=9
M9=ON <=>D0=10
M10=ON <=>D0=11
M11=ON <=>D0=12
M12=ON <=>D0=13
M13=ON <=>D0=14
M14=ON <=>D0=15
M15=ON <=>D0=16
:
M254=ON <=>D0=255
又有何指令支援

如果要"范圍單一M"(M0~M254)轉為D寄存器值或反轉BIT值回M
M0~M254只要一個沒有ON,則D0=0
M0=ON <=>D0=1
M1=ON <=>D0=2
M2=ON <=>D0=3
M3=ON <=>D0=4
M4=ON <=>D0=5
M5=ON <=>D0=6
M6=ON <=>D0=7
M7=ON <=>D0=8
M8=ON <=>D0=9
M9=ON <=>D0=10
M10=ON <=>D0=11
M11=ON <=>D0=12
M12=ON <=>D0=13
M13=ON <=>D0=14
M14=ON <=>D0=15
M15=ON <=>D0=16
:
M254=ON <=>D0=255
又有何指令支援

為何我用
DECO D0 M0 K8
DECO D0 Y0 K8
D0=0   ,Y0=ON  ,M0=OFF
D0=1   ,Y1=ON  ,M1=OFF
D0=2   ,Y2=ON  ,M2=OFF
D0=3   ,Y3=ON  ,M3=OFF
D0=4   ,Y4=ON  ,M4=OFF
D0=5   ,Y5=ON  ,M5=OFF
D0=6   ,Y6=ON  ,M6=OFF
D0=7   ,Y7=ON  ,M7=OFF
D0=8   ,Y8=ON  ,M8=ON
:( 以下D0=9~255;Y M皆可有對應ON)
:

但為何D0=0~7,則M0~M7 皆OFF

============
DECO D0 S100 K8
看來也可對應

不可對應M的原因找到了
我在M0~M7
前面各對應加了X0~X7 開關
作測試用
只是為何如此不行呢

引用

引用第8樓wayu于2019-01-15 13:46發表的  :
FX3U，Q都支持字的位訪問，不要用FX2N了

這位先進 你好

FX3U以前在用時沒注意到位這部份
不知你這位的訪問的使用是如何用
像歐姆龍的W或H類似三菱的M 可以用BIT
不知FX3U如何使用